Wpływ konstrukcji dwuślimakowego układu uplastyczniającego na charakterystykę procesu wytłaczania.

J. Stasiek

Published : 2022-09-17

Vol. 48 No. 6 (2003)

Influence of constructional features of the twin-screw plasticizing system on the characteristic of extrusion process

J. Stasiek

Abstract

The research is focused on the constructional improving of twin-screw co-rotating plasticizing systems by changing the screws' configurations. So the effects of constructional features of such systems on the selected parameters characterizing the process of polypropylene (PP) extrusion, especially on a change of a polymer structure, have been determined. The dependence of extruded PP degradation degree [measured as a change of melt flow rate (MFR) value, Table 4] on the configurations of the screws (Table 2, Fig. 4) has also been evaluated. The changes of the structures of PP compositions containing the additives (e.g. light and thermal stabilizers) have been investigated using DSC (Table 3) and FT- IR (Figs. 5 and 6) methods. It has been found that in the process of discussed co-rotating construction system, the necessity of reaching the required temperature of a polymer during its redrawing to the plasticizing zone, as a result of feeding zone elongation, should be taken into account. Next significant requirement concerns the decrease of drive energy scattering in the plasticizing zone by using of kneading segments supporting the transport and minimization of the channels volume reduction. The assessment (evaluation) of the course of the process of a direct extrusion of PP containing chalk as a filler, dependently on various screws configurations and place of feeding a chalk and chalk amounts, has also been presented. Mechanical properties of the pipes obtained (Table 5, Fig. 8) as well as dispersion degree of the filler in a polymer (Fig. 7) were investigated.

Keywords

współbieżny dwuślimakowy układ uplastyczniający ; wytłaczanie polipropylenu ; konfiguracja ślimaka ; degradacja polimeru ; napełniacz mineralny ; właściwości rur twin-screw co-rotating plasticizing system ; polypropylene extrusion ; screw configuration ; polymer degradation ; mineral filler ; direct extrusion of pipes ; pipes properties

Similar Articles

M. Kmiotek, D. M. Bieliński, M. Piotrowska, W. Jakubowski, Essential oils as biocidal agents in natural rubber vulcanizates , Polimery: Vol. 61 No. 1 (2016)
J. Ryszkowska, M. Zieleniewska, A Bryśkiewicz, K. Mizera, M. Chrząszcz, D. Kozon, K. Lipert, Polyurethane composites with different matrices filled with glass microspheres , Polimery: Vol. 62 No. 1 (2017)
P. Groch, K. Dziubek, K. Czaja, Coordination polymerization of alkenylsilsesquioxanes and their copolymerization with olefins or styrene , Polimery: Vol. 60 No. 5 (2015)
P. Wojciechowska, Z. Foltynowicz, M. Nowicki, Celluloseacetate butyrate nanocomposites synthesized via sol-gel method , Polimery: Vol. 58 No. 7-8 (2013)
P. Staciwa, T. Spychaj, New aromatic diamine-based deep eutectic solvents designed for epoxy resin curing , Polimery: Vol. 63 No. 6 (2018)
E. Kusiak, M. Zaborski, A. Staniszewska, H. Bem, P. Szajerski, W. Baryń, Elastomer shields reducing x-radiation doses in computed tomography techniques , Polimery: Vol. 58 No. 7-8 (2013)
Mariusz Oleksy, Rafał Oliwa, Katarzyna Bulanda, Robert Szałajko, Grzegorz Budzik, Izabela Skrzypczak, Phenol-formaldehyde resin composites filled with modified phlogopite reinforced with hybrid glass and basalt fiber meshes used as grinding wheels , Polimery: Vol. 65 No. 11-12 (2020)
K. Mizera, M. Auguścik, D. Woronka, K. Lipert, W. Kalarus, J. Ryszkowska, Polyurethane composites with mixture of carbon fibers and glass frit , Polimery: Vol. 61 No. 5 (2016)
A. Frańczak, M. Oleksy, R. Oliwa, G. Budzik, Polyethylene composites flame retarded with aluminum hydroxide as coatings for electrical cables , Polimery: Vol. 63 No. 6 (2018)
K. J. Wilczyński, Determination of viscosity curves based on limited rheological measurements , Polimery: Vol. 62 No. 6 (2017)

<< < 90 91 92 93 94 95 96 97 98 99 > >>

You may also start an advanced similarity search for this article.

Details

Statistics

Authors

Download files

PDF (Język Polski)

Zasady cytowania

Stasiek, J. (2022). Influence of constructional features of the twin-screw plasticizing system on the characteristic of extrusion process. Polimery, 48(6), 443–454. Retrieved from https://polimery.ichp.vot.pl/index.php/p/article/view/1883

Citing articles via

Statistics

Total abstract views : 0

PDF Downloads : 0