Application of polymeric materials for obtaining gears with involute and sinusoidal profile

Mariusz Sobolak; Piotr Połowniak; Mariusz Cieplak; Mariusz Oleksy; Katarzyna Bulanda

doi:10.14314/polimery.2020.7.9

Published : 2020-12-16

Vol. 65 No. 7-8 (2020)

Application of polymeric materials for obtaining gears with involute and sinusoidal profile

Mariusz Sobolak Piotr Połowniak Mariusz Cieplak Mariusz Oleksy Katarzyna Bulanda

DOI: https://doi.org/10.14314/polimery.2020.7.9

Abstract

In the article research related to the increasing in the scope of application of additive technologies in the construction of machines for the production of gears with involute and sinusoidal profile from polymeric materials was presented. The designed original research stand and with its use carried out a series of preliminary fatigue tests of the obtained polymer gears with an involute and sinusoidal profile was show. The tested gears were obtained in the technology of rapid prototyping by the FFF (Fused Filament Fabrication) method from polymer composites obtained in the form of an ABS (acrylonitrile/butadiene/styrene) – based filament. Based on the results obtained, it was noticed that the temperature in the meshing zone of the gears with involute profiles is higher than for sinusoidal profiles, regardless of the type of composite from which the gears were made. It should also be noted that in the range of nominal load, the sound intensity level of the meshing zone is also lower for gears with a sinusoidal profile than for gears with an involute profile. Based on the tests carried out, an increase in sound intensity was noticed in the case of gears obtained from selected composites (Table 2) compared to the gear obtained from unfilled ABS. However, in the case of gears obtained from the tested composite materials, we observe a decrease in the gear operating temperature (Table 2). The most favorable results of these tests were obtained for gears with a sinusoidal profile obtained from ABS + P2 composite, which show the lowest operating temperature of the gear. It should also be mentioned that slightly worse results were obtained for involute gears.

Keywords

polymer materials ; polymer machine elements ; FFF (Fused Filament Fabrication) additive technologies ; gears with involute and sinusoidal profile materiały polimerowe ; polimerowe elementy maszyn ; technologia przyrostowa FFF (Fused Filament Fabrication) ; przekładnie zębate o zarysie ewolwentowym i sinusoidalnym

Similar Articles

B. Grabowska, M. Holtzer, Application of spectroscopic methods for investigation of the course of poly(sodium acrylate) crosslinking with use of different crosslinking agents , Polimery: Vol. 53 No. 7-8 (2008)
A. Abramowicz, Comparison of the effect of chosen commercial suspension stabilizers on some properties of poly(vinyl chloride). Part 1, Effect on grain size distribution , Polimery: Vol. 50 No. 7-8 (2005)
Maja Zalega, Joanna Nowak, Kinga Bociong, The influence of quaternary ammonium salts on mechanical properties of light-cured resin dental composites , Polimery: Vol. 68 No. 4 (2023)
S. Łabużek, B. Nowak, J. Pająk, G. Rymarz, Activity of extracellular depolymerase secreted by Gliocladium solani strain during "Bionolle®" polyester degradation , Polimery: Vol. 53 No. 6 (2008)
A. Kloziński, T. Sterzyński, Bagley correction evaluation on the basis of measurements in extrusion line , Polimery: Vol. 50 No. 6 (2005)
R. Ukielski, F. Ł. Kondratowicz, Kondratowicz - Fibre-grade copoly(oxyethylene-b-ethylene terephthalate)s with improved optical properties , Polimery: Vol. 53 No. 3 (2008)
K. Wilpiszewska, T. Spychaj, Chemical modification of starch by reactive extrusion , Polimery: Vol. 53 No. 4 (2008)
J. Przybylski, Associative polyurethane modifiers of rheological properties of aqueous dispersions of polymers. Part 1, The role of rheological properties' modifiers in coating or adhesive materials based on aqueous dispersions of polymers and methods of polyurethane m , Polimery: Vol. 53 No. 4 (2008)
J. Maślińska-Solich, E. Gibas, S. Kukowka, The formation of macrocyclic compounds with O,O- and O,N-acetal units , Polimery: Vol. 50 No. 7-8 (2005)
Małgorzata Oleksy, Klaudia Dynarowicz, David Aebisher, Polymer composites for obtaining human anatomic structures , Polimery: Vol. 68 No. 6 (2023)

<< < 77 78 79 80 81 82 83 84 85 86 > >>

You may also start an advanced similarity search for this article.

Details

References

Statistics

Authors

Download files

PDF

Zasady cytowania

Sobolak, M., Połowniak, P., Cieplak, M., Oleksy, M., & Bulanda, K. (2020). Application of polymeric materials for obtaining gears with involute and sinusoidal profile. Polimery, 65(7-8), 563–567. https://doi.org/10.14314/polimery.2020.7.9

Altmetric indicators

Citing articles via

Statistics

Total abstract views : 0

PDF Downloads : 0

Mariusz Sobolak msobolak@prz.edu.pl

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Piotr Połowniak

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Mariusz Cieplak

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Mariusz Oleksy

Affiliation
Faculty of Chemistry, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Katarzyna Bulanda

Affiliation
Faculty of Chemistry, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland