Application of polymeric materials for obtaining gears with involute and sinusoidal profile

Mariusz Sobolak; Piotr Połowniak; Mariusz Cieplak; Mariusz Oleksy; Katarzyna Bulanda

doi:10.14314/polimery.2020.7.9

Published : 2020-12-16

Vol. 65 No. 7-8 (2020)

Application of polymeric materials for obtaining gears with involute and sinusoidal profile

Mariusz Sobolak Piotr Połowniak Mariusz Cieplak Mariusz Oleksy Katarzyna Bulanda

DOI: https://doi.org/10.14314/polimery.2020.7.9

Abstract

In the article research related to the increasing in the scope of application of additive technologies in the construction of machines for the production of gears with involute and sinusoidal profile from polymeric materials was presented. The designed original research stand and with its use carried out a series of preliminary fatigue tests of the obtained polymer gears with an involute and sinusoidal profile was show. The tested gears were obtained in the technology of rapid prototyping by the FFF (Fused Filament Fabrication) method from polymer composites obtained in the form of an ABS (acrylonitrile/butadiene/styrene) – based filament. Based on the results obtained, it was noticed that the temperature in the meshing zone of the gears with involute profiles is higher than for sinusoidal profiles, regardless of the type of composite from which the gears were made. It should also be noted that in the range of nominal load, the sound intensity level of the meshing zone is also lower for gears with a sinusoidal profile than for gears with an involute profile. Based on the tests carried out, an increase in sound intensity was noticed in the case of gears obtained from selected composites (Table 2) compared to the gear obtained from unfilled ABS. However, in the case of gears obtained from the tested composite materials, we observe a decrease in the gear operating temperature (Table 2). The most favorable results of these tests were obtained for gears with a sinusoidal profile obtained from ABS + P2 composite, which show the lowest operating temperature of the gear. It should also be mentioned that slightly worse results were obtained for involute gears.

Keywords

polymer materials ; polymer machine elements ; FFF (Fused Filament Fabrication) additive technologies ; gears with involute and sinusoidal profile materiały polimerowe ; polimerowe elementy maszyn ; technologia przyrostowa FFF (Fused Filament Fabrication) ; przekładnie zębate o zarysie ewolwentowym i sinusoidalnym

Similar Articles

E. Kowalska, T. Wielgosz, T. Bartczak, Utilization of glass fiber-reinforced polyester laminate wastes , Polimery: Vol. 47 No. 2 (2002)
M. Zaborski, T. Paryjczak, A. Kaźmierczak, J. Albińska, Characterization of physicochemical properties of the inorganic components in the "core-shell"-structured polymer mixtures. Part I. The precipitated silica systems , Polimery: Vol. 47 No. 2 (2002)
A. Rozpłoch, A. Stasiek, J. Dzwonkowski, J. Patyk, J. Czypryńska, X-ray diffration studies on the degree of crystallinity in polypropylene films by the Marquart—Levenberg optimization procedure , Polimery: Vol. 47 No. 2 (2002)
M. Białek, A. Utrata, K. Czaja, Studies on ethyl ene/1-hexene copolymerization over the zirconocene catalyst supported on MAO-modified MgCl2(THF)(2) , Polimery: Vol. 47 No. 1 (2002)
S. Płaska, The method for selecting the strategy to control the quality of injection moldings , Polimery: Vol. 47 No. 1 (2002)
J. Czupryńska, The effect of high-energy electron beam radiation on polymer properties , Polimery: Vol. 47 No. 1 (2002)
E. Hałasa, Synthesis and properties of polyphenylenes , Polimery: Vol. 47 No. 1 (2002)
W. Ochędzan-Siodlak, B. Mazoń, Effect of sample preparation on gel permeation chromatography results of determination of molecular weight of polyethylene obtained with using of zirconocene catalyst activated with methyl aluminoxane , Polimery: Vol. 48 No. 11-12 (2003)
L. Krochmalowa, Poly(vinyl chloride)/epoxy composition as an example of polymer/oligomer composites in the paint coatings , Polimery: Vol. 48 No. 11-12 (2003)
M. Uhniat, M. Zemlak, S. Kudła, W. Balcerowiak, Rheometric studies on the processes of crosslinking of polyethylene and ethylene copolymers in the presence of peroxides. , Polimery: Vol. 48 No. 11-12 (2003)

<< < 89 90 91 92 93 94 95 96 97 98 > >>

You may also start an advanced similarity search for this article.

Details

References

Statistics

Authors

Download files

PDF

Zasady cytowania

Sobolak, M., Połowniak, P., Cieplak, M., Oleksy, M., & Bulanda, K. (2020). Application of polymeric materials for obtaining gears with involute and sinusoidal profile. Polimery, 65(7-8), 563–567. https://doi.org/10.14314/polimery.2020.7.9

Altmetric indicators

Citing articles via

Statistics

Total abstract views : 0

PDF Downloads : 0

Mariusz Sobolak msobolak@prz.edu.pl

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Piotr Połowniak

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Mariusz Cieplak

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Mariusz Oleksy

Affiliation
Faculty of Chemistry, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Katarzyna Bulanda

Affiliation
Faculty of Chemistry, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland