Application of polymeric materials for obtaining gears with involute and sinusoidal profile

Mariusz Sobolak; Piotr Połowniak; Mariusz Cieplak; Mariusz Oleksy; Katarzyna Bulanda

doi:10.14314/polimery.2020.7.9

Published : 2020-12-16

Vol. 65 No. 7-8 (2020)

Application of polymeric materials for obtaining gears with involute and sinusoidal profile

Mariusz Sobolak Piotr Połowniak Mariusz Cieplak Mariusz Oleksy Katarzyna Bulanda

DOI: https://doi.org/10.14314/polimery.2020.7.9

Abstract

In the article research related to the increasing in the scope of application of additive technologies in the construction of machines for the production of gears with involute and sinusoidal profile from polymeric materials was presented. The designed original research stand and with its use carried out a series of preliminary fatigue tests of the obtained polymer gears with an involute and sinusoidal profile was show. The tested gears were obtained in the technology of rapid prototyping by the FFF (Fused Filament Fabrication) method from polymer composites obtained in the form of an ABS (acrylonitrile/butadiene/styrene) – based filament. Based on the results obtained, it was noticed that the temperature in the meshing zone of the gears with involute profiles is higher than for sinusoidal profiles, regardless of the type of composite from which the gears were made. It should also be noted that in the range of nominal load, the sound intensity level of the meshing zone is also lower for gears with a sinusoidal profile than for gears with an involute profile. Based on the tests carried out, an increase in sound intensity was noticed in the case of gears obtained from selected composites (Table 2) compared to the gear obtained from unfilled ABS. However, in the case of gears obtained from the tested composite materials, we observe a decrease in the gear operating temperature (Table 2). The most favorable results of these tests were obtained for gears with a sinusoidal profile obtained from ABS + P2 composite, which show the lowest operating temperature of the gear. It should also be mentioned that slightly worse results were obtained for involute gears.

Keywords

polymer materials ; polymer machine elements ; FFF (Fused Filament Fabrication) additive technologies ; gears with involute and sinusoidal profile materiały polimerowe ; polimerowe elementy maszyn ; technologia przyrostowa FFF (Fused Filament Fabrication) ; przekładnie zębate o zarysie ewolwentowym i sinusoidalnym

Similar Articles

J. Pielichowski, A. Prociak, S. Michałowski, D. Bogdał, Application of selected polymeric wastes in the formulation of rigid polyurethane foams , Polimery: Vol. 55 No. 10 (2010)
K. Formela, M Cysewska, Efficiency of thermomechanical reclaiming of ground tire rubber conducted in counter-rotating and co-rotating twin screw extruder , Polimery: Vol. 59 No. 3 (2014)
D. Kolasa, A. Bajszczak, A. Łukomska, J. Dłubak, Z. Rogulski, S. Kowalska, A. Czerwiński, Analysis of metals content in polyethylene packaging materials in view of the existing legislation , Polimery: Vol. 61 No. 2 (2016)
Danuta Matykiewicz, Olga Mysiukiewicz, Epoxy composites reinforced with natural fillers such as flax fiber and linseed cakes , Polimery: Vol. 65 No. 11-12 (2020)
G. Mitchener, Impact of Grenfell Tower fire disaster on polyisocyanurate industry , Polimery: Vol. 63 No. 10 (2018)
M. Kwiatkowska, I. Kowalczyk, A. Szymczyk, K. Gorący, Effect of thermal aging on the crystalline structure and mechanical performance of fully bio-based, furan-ester, multiblock copolymers , Polimery: Vol. 63 No. 9 (2018)
Stanisław Rabiej, Małgorzata Rabiej, A comparison of the structure of lamellar stacks in a semicrystalline polymer during melting and crystallization by means of the Intensity Superposition Method , Polimery: Vol. 65 No. 9 (2020)
A. Niemczyk, K. Dziubek, K. Czaja, R. Szatanik, M. Szołyga, M. Dutkiewicz, B. Marciniec, Polypropylene/polyhedral oligomeric silsesquioxane nanocomposites – study of free volumes, crystallinity degree and mass flow rate , Polimery: Vol. 61 No. 9 (2016)
D. Pieczyńska, U. Ostaszewska, D. M. Bieliński, J. Jagielski, Modification of polymers with the application of ion beam bombardment. Part I. History, recent developments, and perspectives for development , Polimery: Vol. 56 No. 6 (2011)
U. Edlund, A.-Ch. Albertsson, A controlled radical polymerization route to polyepoxidated grafted hemicellulose materials , Polimery: Vol. 59 No. 1 (2014)

<< < 35 36 37 38 39 40 41 42 43 44 > >>

You may also start an advanced similarity search for this article.

Details

References

Statistics

Authors

Download files

PDF

Zasady cytowania

Sobolak, M., Połowniak, P., Cieplak, M., Oleksy, M., & Bulanda, K. (2020). Application of polymeric materials for obtaining gears with involute and sinusoidal profile. Polimery, 65(7-8), 563–567. https://doi.org/10.14314/polimery.2020.7.9

Altmetric indicators

Citing articles via

Statistics

Total abstract views : 0

PDF Downloads : 0

Mariusz Sobolak msobolak@prz.edu.pl

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Piotr Połowniak

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Mariusz Cieplak

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Mariusz Oleksy

Affiliation
Faculty of Chemistry, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Katarzyna Bulanda

Affiliation
Faculty of Chemistry, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland