Application of polymeric materials for obtaining gears with involute and sinusoidal profile

Mariusz Sobolak; Piotr Połowniak; Mariusz Cieplak; Mariusz Oleksy; Katarzyna Bulanda

doi:10.14314/polimery.2020.7.9

Published : 2020-12-16

Vol. 65 No. 7-8 (2020)

Application of polymeric materials for obtaining gears with involute and sinusoidal profile

Mariusz Sobolak Piotr Połowniak Mariusz Cieplak Mariusz Oleksy Katarzyna Bulanda

DOI: https://doi.org/10.14314/polimery.2020.7.9

Abstract

In the article research related to the increasing in the scope of application of additive technologies in the construction of machines for the production of gears with involute and sinusoidal profile from polymeric materials was presented. The designed original research stand and with its use carried out a series of preliminary fatigue tests of the obtained polymer gears with an involute and sinusoidal profile was show. The tested gears were obtained in the technology of rapid prototyping by the FFF (Fused Filament Fabrication) method from polymer composites obtained in the form of an ABS (acrylonitrile/butadiene/styrene) – based filament. Based on the results obtained, it was noticed that the temperature in the meshing zone of the gears with involute profiles is higher than for sinusoidal profiles, regardless of the type of composite from which the gears were made. It should also be noted that in the range of nominal load, the sound intensity level of the meshing zone is also lower for gears with a sinusoidal profile than for gears with an involute profile. Based on the tests carried out, an increase in sound intensity was noticed in the case of gears obtained from selected composites (Table 2) compared to the gear obtained from unfilled ABS. However, in the case of gears obtained from the tested composite materials, we observe a decrease in the gear operating temperature (Table 2). The most favorable results of these tests were obtained for gears with a sinusoidal profile obtained from ABS + P2 composite, which show the lowest operating temperature of the gear. It should also be mentioned that slightly worse results were obtained for involute gears.

Keywords

polymer materials ; polymer machine elements ; FFF (Fused Filament Fabrication) additive technologies ; gears with involute and sinusoidal profile materiały polimerowe ; polimerowe elementy maszyn ; technologia przyrostowa FFF (Fused Filament Fabrication) ; przekładnie zębate o zarysie ewolwentowym i sinusoidalnym

Similar Articles

Z. Wiącek, Estimation of adhesive properties of oxidated surfaces of aluminum alloys in the light of theory of adsorption , Polimery: Vol. 48 No. 3 (2003)
S. Kudła, Assessment of the influence of mineral fillers on polyethylene crosslinking in the presence of peroxide by rheometric method , Polimery: Vol. 54 No. 7-8 (2009)
F. Bondioli, V. Cannillo, E. Fabbri, M. Messori, Preparation and characterization of epoxy resins filled with submicron spherical zirconia particles , Polimery: Vol. 51 No. 11-12 (2006)
Gang Xu, Shiwei Wang, Long Zhang, Long Wu, Basic magnetization curve fitting function based on spectral analysis , Polimery: Vol. 70 No. 2 (2025)
K. Wilczyński, Z. Szymaniak, A. Nastaj, Modeling of plastics coextrusion. Part I. Viscous flows , Polimery: Vol. 48 No. 3 (2003)
Mujtahid Kaavessina, Sperisa Distantina, Muhamad Rizki Hi. Wahab, Natasya Yola Ferdilla, Joko Waluyo, Characteristics of antistatic packaging material based on polypropylene and activated carbon derived from coconut shells as filler , Polimery: Vol. 70 No. 4 (2025)
S. Kuciel, A. Liber-Kneć, S. Zajchowski, Biocomposites based on thermoplastic starch or polylactide/starch blends as the matrices filled with natural fibers , Polimery: Vol. 54 No. 10 (2009)
T. Sterzyński, I. Śledź, Polypropylene monopolymer composites - preparation, structures and properties , Polimery: Vol. 52 No. 6 (2007)
J. Stasiek, Modern technologies and equipment for blowing extrusion of the films. Part 2, Trends in development of processing lines for one-stage blowing extrusion of the films , Polimery: Vol. 50 No. 5 (2005)
W. Fabianowski, B. Polak, M. Lewandowska-Szumieł, Polymers for bone reconstruction - evaluation of chosen polimeric substrates in osteoblasts in vitro culture , Polimery: Vol. 49 No. 7-8 (2004)

<< < 50 51 52 53 54 55 56 57 58 59 > >>

You may also start an advanced similarity search for this article.

Details

References

Statistics

Authors

Download files

PDF

Zasady cytowania

Sobolak, M., Połowniak, P., Cieplak, M., Oleksy, M., & Bulanda, K. (2020). Application of polymeric materials for obtaining gears with involute and sinusoidal profile. Polimery, 65(7-8), 563–567. https://doi.org/10.14314/polimery.2020.7.9

Altmetric indicators

Citing articles via

Statistics

Total abstract views : 0

PDF Downloads : 0

Mariusz Sobolak msobolak@prz.edu.pl

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Piotr Połowniak

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Mariusz Cieplak

Affiliation
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Mariusz Oleksy

Affiliation
Faculty of Chemistry, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland

Katarzyna Bulanda

Affiliation
Faculty of Chemistry, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland